Quantcast
Channel: AcuraZine - Acura Enthusiast Community
Viewing all 44237 articles
Browse latest View live

Transmission problem

$
0
0
Hi, I have a 2006 TL with the 5AT. Yesterday, the transmission acted of a really weard way. For exemple, it was on the second gear and the engine always varied between 1500 and 2400rpm when I was on a constant speed. In the car, I could feel the shots when the engine was dropping or increasing in rpm. It acted of the same way with the others gears and the green light next to the D was flashing. After some miles, I stop the engine and the transmission seems to be ok since this moment. It is the second time that the transmisson does that. The oil is new and the level is correct. What could be the problem? I hope tje tranny is not going to went out!!!

Also, I think that the transmission is slipping a lot. When I am at 50mph, the engine is at about 1600-1700rpm and if I keep the same speed and I climb a coast, the rpm will increase to 2300-2400rpm but it will stay on the fifth gear. I have to push more on the gas pedal if I want the transmission to downshift to the fourth gear. I deduced that the transmission was slipping. Is that normal or not??

Sorry if I am hard to read, I am French, thanks.

P0330 - Knock Sensor

$
0
0
Hi everyone, I'm new to this forum and I would love some help with my 1996 Acura RL. My check engine light came on and I got the code P0330 - knock sensor 2 (bank 2).

Could anyone help me out with where this sensor is? Do I have to take the manifold out to reach it?

Thanks.

DIY: Rear View Mirror Rattle fix

$
0
0
Hey guys, not sure if this is already here or not but I thought I would do a write up for it.

The other day I noticed my mirror was bouncing around slightly and then today it was a little worse, so I pulled it apart and fixed it after work today. Super simple to do and it's another rattle of the list.

Tools you will need:
-Pliers of any sort (I used needle nose)
-Panel tool

Click the image to open in full size.

There's 3 pieces that come off one closest to the windshield, one on the opposite end of the mirror arm, and one on the headliner.

Click the image to open in full size.

Pop all three off and unplug the mirror wire from the connector in the headliner. Then slide the mirror down the window off the 'hook', if your mirror was rattling it will likely easily slide off.

** Be careful when popping the mirror arm trim off, it's only held on by tiny plastic barbs and they can be easily damaged. If they are they won't clip back in properly or very tight. This happened to me on the trim piece facing the back of the car, and now I will need to buy a new trim piece. I'm hoping to god it comes separate of the mirror assembly! Otherwise, glue it is :tomato:

Click the image to open in full size.

Click the image to open in full size.

The reason for the rattling comes from this metal clip here. Over time and bass and bumps the clip gets stretched, hence rattle.
Squeeze both clips together till they are slightly*** bent closer than before. If you bend it too far the mirror may not slide back onto the mount on the windshield.

If you want to go the extra mile and be careful, you can remove the bracket by taking out the torx screw holding it on and bend it back while it's not attached to the mirror. Then re-attach it.

Click the image to open in full size.

Click the image to open in full size.

Then reattach and clip the panels back into place and you're good to go, rattle free!

coupe rendered

Valve adjustment with Timing Belt Service?

$
0
0
So I took the car in for a state and emissions inspection so I could get new tags. The dealer I go to is cheaper than any other place ($36). The service rep noticed my mileage and saw that my 105k will need to be done probably by October. The dealer quoted a (ridiculous) price of $1400 for that. He then stated that it is probably due for a valve adjustment as well ($600). Likely I can space this out but is it recommended to have this done around the same time? Hopefully there is (considerable) wiggle room in these prices.

Lug Nuts for Stock Wheels 07 Base

$
0
0
All of my lugs are old and beat up and look horrible, not to mention are getting a little hard to get on and off at times.

If possible Id like to get a black set? What kind of seats do I need to look for?

I thought they were ball style, but haven't been able to find out if that is the correct style or not?

Camber Adjusting Ball Joints vs. Adjustable upper arms

$
0
0
I am planning on replacing some bad ball joints in my '02, and am planning to eventually lower it.


I've never used the adjustable ball joint camber links before and wanted to know if they were any good when compared to a "real" adjustable upper arm kit which is what I am used too and have experience with.


At first glance they seem like they would need regular adjustment, and frankly seem wonky. Anyone with experience with these? http://www.moogproblemsolver.com/ste...ent-ball-joint

Debating a TLX

$
0
0
Hey all new here and new to the Acura community in general.

Both of my parents own an Acura and absolutely love it, I got addicted to some of the higher end cars more recently.

I currently own an 03 325i and I love the car, but alas its 12 years old and its getting to be time to upgrade.

I've test driven quite a few cars Mazda 3, Nissan Altima, Ford Fusion, and they are all quite nice. However, I feel like the Acura may be more up my alley.

Everyone on here claims and raves about how much value you get for the 4 cylinder with the tech package. Can you guys explain or help out some with what kind of performance I can expect from the car. I love the acceleration on my 325i which isn't even all that much at over 7 seconds 0-60. The car will also take off from 60+ and imo handles really well.

What can I expect from this new Acura as there isn't a whole lot of information out there about it. A 5k Tech package seems like a lot to me, when something like a Mazda 3 offers a similar Tech for 3k. That said I'll be the first to say I haven't done a lot of research on the higher end market as I don't want to be spending over 40k to get a fully loaded car.

Any advice or input is appreciated! Thanks in advance!

FS: Ported and Polished Intake Runner

$
0
0
Hey, have a set of ported runners for sale. They fit 7th Gen 3.0 Accords and 3rd Gen 3.2-3.5 TL's. I personally did the work. Let me know if you have any questions.


- $190 shipped (With PP fees)
- $180 Shipped (Send money as friend)

Click the image to open in full size.

BEFORE
Click the image to open in full size.

AFTER
Click the image to open in full size.

BEFORE
Click the image to open in full size.

AFTER
Click the image to open in full size.

FS: 2007 tl black on black aspec los angeles, ca

$
0
0
1. Price: 11000 obo
2. Mileage: 117xxx
3. Color, Transmission-auto or manual, Navi: Black, 5-Speed Automatic
4. Reason for selling: Parting Ways
5. Location: Los Angeles, CA.
6. Pictures: SEE BELOW
7. Are you the first owner? If not, how many owners were there (to the best of your knowledge)? 1 OWNER
8a. Title is clean/clear/rebuilt/salvage/if other, explain further (select one): CLEAN
8b. Do you have title in hand or it is being held by a lienholder: TITLE IN HAND
9. VIN (would be nice to have but I can understand that some people do not want to publicly post this): upon request
10. Modifications: A-Spec Lip Kit, Megan Racing Coilovers with 5k miles, 19" Avant Garde Wheels, Window Tint
11. Service record: services done by myself
12. If leased, provide details, such as length of lease, payoff amount, etc. title in hand

I'm posting up my 2007 ACURA TL (A-SPEC) for sale. I am the first and only owner who mainly utilized the car for cruising and commutting. Some of the few minor modifications consist of Megan Racing coilovers, A-SPEC LIP KIT, 19 X 8.5 Avant Garde wheels, and 15% visibility window tint. The car's oem paint is still in very good condition: washed and detailed with Meguiar's products only. All scheduled oil and oil filter changes were done by myself before or at every 5k miles with only Mobil 1 synthetic oil. The 105k maintenance was done in 10/2013, which includes timing belt, water pump, tensioner, coolant, and serpentine belt. The 3 engine mounts and 2 transmission mounts were also replaced during the 105k maintenance service.

asking price is 11000 OBO aggressive seller
626-673-8895

Really strange HID light issue

$
0
0
Ever since I got my TL back in February, I've been having a weird issue with the passenger side light.
It would turn on and stay on every time as long as I only turned it on once. Say I turned the lights on, pulled up to somebody's house to pick up a friend, shut them off, then turn them back on when friend jumps in the car, the passenger side wouldn't come back on..
Say instead of waiting outside in the car, I stopped inside my friend's house for a few minutes to visit and then went back out, the passenger light would turn on fine.
If I left my lights on overnight (auto off) and then come out in the morning, used my FOB to unlock car (lights flash), then jump in the car and start it, passenger light goes out due to lights turning off while cranking motor.

See where I'm going with this?

NOW RECENTLY it will not come on no matter what trick I do,
it's purely chance. Comes on maybe 1 in 10 times.

And about three days later, passenger's side comes on, but now DRIVER'S side doesn't.

cycle the headlights on and off a few times and the driver's side comes on but passenger is still off. cycle them a few more times and now they won't turn on at all until car is left alone for a while.

Any idea what this could be?

FS: Complete '07-'08 TL Front Grill Assembly - NEW

$
0
0
FOR SALE:

Complete Front Grill Assembly + Lower Grill Trim Pieces, and Hood Trim for '07-'08 TL.

My buddy sold his TL and sent me some leftover parts to use and / or sell. These particular pieces do not fit my '04, so I have decided to sell them. They have never been mounted to a vehicle, but they were plastidipped in preparation to do so. All of the visible plastidip has been removed, but there may still be some remaining on the backsides (not visible, and removable if you wish to do so).

I'm selling everything for $125 + shipping, but will consider selling individual pieces if no one snags the whole package.
Click the image to open in full size.


Included Pieces:

-Mesh (Honeycomb) Grill Piece. Part #71120-SEP-A10ZA. $10 + Shipping.
Click the image to open in full size.

-Center Emblem Plate + Emblem. Part #75705-SEP-A10ZA. $50 + Shipping.
Click the image to open in full size.

-Lower Front Grill Molding V-Piece. Part #75125-SEP-A10ZA. Notice: This part was apparently damaged in shipping. It appears to have a slight bend, and 1 of the 8 clips are loose. However, I do not foresee any issues with getting it installed. $25 + Shipping.
Click the image to open in full size.

-Hood Trim Piece. Part #75120-SEP-A00. $40 + Shipping.
Click the image to open in full size.

-Both Lower Grill Trim Pieces. Part #'s 71121-SEP-A10ZA and 71126-SEP-A10ZA. $20 + Shipping (for both).
Click the image to open in full size.

Thanks for looking! Let me know if you have any questions.

Police Stop High School Shooting Plot

$
0
0
This really hits close to home as this school is close to me. Kind of surprising since this is a highly rated High School in a fairly affluent neighborhood > http://www.usnews.com/education/best...gh-school-3484


http://www.latimes.com/local/lanow/l...818-story.html

Originally Posted by :
2 students held in mass-shooting plot at South Pasadena High, police say

Police said Monday that they uncovered a mass-shooting plot at South Pasadena High School, arresting two students on suspicion of planning to "kill three staff members and as many students as possible with firearms."

The two students were arrested after detectives served search warrants at their homes, according to the South Pasadena Police Department.

One of the students resisted arrest, prompting officers to force their way into his home, according to police officials.

"He was captured in the home as he tried to run away," Sgt. Brian Solinsky said in a statement.

He said that school officials became aware of suspicious behavior and contacted law enforcement authorities.

"It was this information that helped prevent a horrific tragedy," Solinsky said.

He did not respond Monday night to a request for comment, but he said in his statement that police would be releasing details on the case at a news conference Tuesday morning.

South Pasadena Unified School District Supt. Geoff Yantz said that school administrators were informed of a "credible threat of potential school violence" and immediately contacted police.

"The police have the situation under control and there is currently no threat to students or employees," Yantz said in a statement.

He said psychologists and counselors will be at the school to support students and employees. Classes start Thursday.

Two school parents said Monday night that they were glad that police acted quickly.


http://www.pasadenastarnews.com/gene...-mass-shooting

Originally Posted by :
Two South Pasadena High students arrested in connection with potential mass shooting

Police on Monday arrested two students suspected of planning a mass school shooting that targeted teachers and students at South Pasadena High School.

School officials reported the suspected plot to police on Thursday, but did not say how they learned of it. The pair had been under surveillance since the report, South Pasadena police Sgt. Brian Solinsky said.

He would not elaborate on the plans or what form they took, but Solinsky said they were “very specific” and included named targets.

“This is a prime example of school officials recognizing suspicious behavior,” Solinsky said in a statement. “It was this information that helped prevent a horrific tragedy.”

Police found no weapons in either of the student’s possession or in their homes, authorities said.

“Any time something like this comes up, it certainly causes great concern, not just for South Pasadena, but public schools across the country,” South Pasadena Unified School District Superintendent Geoff Yantz said.

Police said they did not find guns or other weapons in the boys’ homes. However, officials said the boys had been researching weapons on the internet.

A spokeswoman with the Los Angeles County District Attorney’s office said she was uncertain if charges had been presented by police.

Sgt. Robert Bartl said the suspects researched rifles, handguns, submachine guns, bombs and explosives, specifically propane.

“They were researching weapons and how to fire and assemble them,” Bartl said.

Bartl said a submachine gun can fire several rounds per second and can “cause catastrophe.”

The boys told police during the investigation what they had researched. Police did not know when they were planning to carry out the shooting.

Bartl said detectives obtained evidence where the boys listed the names of three teachers and two students who they wanted to kill.

Their identities were not available.

Los Angeles County criminalists Monday searched the suspects’ computers’ for files and history, Bartl said.

South Pasadena Police officials plan to hold a news conference Tuesday morning to discuss the arrests.

“I don’t know how it was reported to (the school), they got knowledge from some source and then it was reported to us,” he said.

Patrol officers were immediately sent to the school to take an initial crime report and detectives followed leads and tips, Bartl said.

“Detectives served warrants at each of the suspect’s homes,” officials said. “Enough evidence was discovered, and based on that evidence the suspects were arrested at their homes.”

One of the suspects was arrested without incident.

The second suspect resisted arrest and officers had to force entry into his house, officials said. Reportedly, he was captured in the home as he tried to run away from the arresting officers.

“School doesn’t start until Thursday and that was one of our goals — to make sure the investigation was moving very quick,” Bartl said. “(We) had detectives working nonstop the last four-to-five days since we received the actual report so that we could put a stop to this prior to school starting.”

“(We’re) pretty confident that we’re going to find more evidence on the computers, and through their statements to us, that they were using their computers to research weapons,” Bartl said.

Detectives have not spoken to any students, but spoke with the teachers who were named on the suspects’ list, Bartl said.

Yantz did not know how long the three teachers have been employed with the school.

“We will be providing support services to students, faculty and employees who feel the need to have such support,” Yantz said. “As a precautionary measure there will be additional police presence on campus to start the school year.”

Yantz did not comment on whether or not the school had past issues with the suspects.

A letter was sent out Monday night via email to parents notifying them of the incident and offering counseling for students.

Bartl said the boys planned to carry out their attack for personal reasons.

“They may have been crossed by one of the students or teachers, maybe by how the teacher taught or a grade (one of the suspects) received,” Bartl said. “It was definitely directed toward people they weren’t happy with.”

No additional suspects are being sought in connection with the recent planned shooting, Bartl said. Police said they will give an update at a news conference at 10 a.m. Tuesday.

Anyone with more information is asked to call South Pasadena Police Department Detectives at 626-403-7297.

new front pads and rotors issues

$
0
0
Hey there just swapped front pads and rotors. Rotors are cross drilled and slotted replacements from Powerstop, Amazon sent pads for 5AT instead of the 6MT kit I ordered. Bitching complete... I went to Advanced and grabbed the wearever platinums. Lo and behold they fit, sorta. The new pads are right up againdt the rotors, I figured that could be expected with a higher performance rotor and longer life pads (they seem a bit thicker than new OE pads) Now after a couple days of drivimg and a proper seat and bed they are still touching the rotor AND grabbing enough to bog the car. Swapping back to stock is not an option at this point as the OE pads/rotors are horrendously worn out (rotor is grooved inside pass side pad worn to the pad screws). I also get a decent amount of wobbling/vibration when braking +60 mph. I should hope the damn rotor isnt warpped with less than 1000 mi in the middle of summer. I love this car, and cringe when its suck pleeeeeease help help help.
AfgVetTL
Kenny

Tarnsmission and Brakes Help!!!

$
0
0
I drive an automatic 2004 rsx. Yesterday I took it to Jiffy Lube to get the oil changed as well as the tarnsmission fluid exchange and powersteering fluid exchange. As soon as I got my car back it was not running right at all. The gears were not changing, I was only driving 20mph at it was 3000+ revs. The brakes were locked up, I could not hit the brake pedal at all and the car would completley stop even if it was on neutral. I took it back to the jiffy lube and they said they had no idea what was wrong with it, after about 20 minutes of playing with it, it magically worked again. They did not have a mechanic to take a look at it so they told me to go in today but I had to work so I did not get a chance. Point it this morning the car is having the same issues. I heard it might be an issue with the air in the transmission fluid. Does anyone have any idea what happened and what it will take to fix the issue?

04 tl auto trans fix?

$
0
0
Ok i have the infamous transmission slipping problem car is at 189k would changing the solenoids and torque converter solve my issue? Or does it have to be rebuilt

Getting the Oddessy transmission swap done tomorrow. FEW QUESTIONS..

$
0
0
Hi I'm getting my Oddessy transmission swap done tomorrow FINALLY... Yes I've used the search function. But what is the longevity of these transmissions I picked one up with 70K miles. And for the ones who have done this swap how has yours been treating you? I'm looking forward to many more miles of transmission free issues..

Side note i also picked up a motor with 80k miles on it since i had a rod knock on my engine. My next question is how would the Oddessy transmission hold up to a low-moderate boost turbo setup? ?

non-cmbs grill on cmbs

$
0
0
Has anyone tried to use a non cmbs grill on a cmbs equipped car? Just curious to see what the results were. The grill is terrible looking and I would love to figure out an alternative.

Need Sub recommendations plz..Just got a JL Audio 300/4 and pair of MB Quart speakers

$
0
0
Guys,

Old school setup! lol

I just got a hold of an old JL Audio 300/4 and a pair of old MB Quart QSD216 speakers that I plan on using for the front of my 04 TL (hopefully they fit).

I would like to add one sub to run in bridged mode for the other two channels of the 300/4.

What's the best way to do this? would a line converter work? Or would I need a sound processor?

Also, I have no idea how to set up the crossovers for the quarts. If anyone can help me with that, I would appreciate it.

It's been a while since I've messed around with car audio so bear with me.

Budget: I would like to spend maybe $300 or less for the sub. I know it's not a lot, but it's what it is..

Also, how to:

Tap into the factory amp for the leads to the front speaker and the rear sub.. Which wires are which? Which are the inputs to the factory amp? Does anyone have pics?

Thanks.

RL Rear View Camera wire functions

$
0
0
I am in the process of installing a backup camera on my 2006 RL. I installed a camera about 6 months ago, but the cheap camera has seriously degraded over the hot summer months, so I have acquired an original acura camera
P/N 08A21-6F0-360-01 to replace the cheap Chinese knock off. The camera comes with pins already crimped on the wires, but there is no connector shell. I am going to use the shell I had already, so I'm looking for something that gives me the functions for the various wires


red/red
blk/blk
wht/wht
yel/yel
blk/blu
brown


Does anyone have a source document that describes the functions for these leads?
Viewing all 44237 articles
Browse latest View live